The integrated zone amplifier offers a variety of easy-to-use input connections (mic/line/page), input gain and output level adjustments, and operational modes. Built-in FreeSpace 3 System, FS3B subwoofer, FreeSpace FS2 and FS4, and DesignMax DM2 and DM3 loudspeaker EQ presets can be selected for loudspeaker optimization.

With a switch on the rear panel, selectable Bose Professional loudspeaker EQ presets optimize performance of the following loudspeakers:

– IZA 2120-LZ: Flat, FreeSpace FS2, FS4, DesignMax DM2, DM3

– IZA 2120-HZ: HPF, FreeSpace FS2, FS4, DesignMax DM2, and SUB

Bose Professional dynamic equalization is a DSP function that ensures full and balanced music at any volume level.

Opti-Voice paging equalizes the vocal frequency range for clear speech intelligibility while providing seamless transitions.

System setup is done locally from the front and rear panels. No computer required

Rear panel DIP switches offer the following flexible operation modes:

– IZA 2120-LZ: Output (Mono/Stereo), A/B Select (Front/Remote), Auto Standby (Off/On), Page Bypass Master (Off/On), Page Mode (Duck/Mix), Page Start (PTT/VOX), Aux Output (Flat/EQ), Aux Output (Fixed/Variable), Aux Input (Enabled/Disabled)

– IZA 2120-HZ: Remote 1 Control (Zone 1/Zone 1+2), A/B Select (Front/Remote), Auto Standby (Off/On), Page Output (Zone 1+2/Zone1), Page Bypass Master (Off/On), Page Mode (Duck/Mix), Page Start (PTT/VOX), Aux Output 1 (Flat/EQ), Aux Output 2 (Flat/EQ), Aux Output (Fixed/Variable), Aux Input (Zone 1+2/Zone1), Aux Input (Enabled/Disabled), Output Voltage (70/100V)

Four inputs: two stereo line inputs, one mic/line page input and one auxiliary stereo line input

Input source levels can be adjusted with independent gain controls

Output level (trim) controls available for adjusting individual channel outputs relative to the overall master level

Source select and master output level can be easily controlled from the front panel or remote control

Volume control with A/B switch enables access to amplifier volume level and source selection from remote locations (PC 041967)

Auxiliary input on front panel allows quick connection to mobile devices

Fine tune the sound with front panel treble and bass tone control knobs (±6 dB @ 100 Hz and 7 kHz). The IZA 2120-HZ has two sets of treble and bass tone control knobs, one for each zone output.

Amplifier outputs can be muted remotely via a contact closure

High- and low-impedance models available. Choose between 2 channels at 120 watts (model IZA 2120-LZ, 4Ω) or 2 channels at 120 watts (model IZA 2120-HZ, 70/100V systems) for loudspeaker installations.

Compact, lightweight design. Can be rack-mounted with included rack ears, or placed of the way on a table, desk, counter or shelf.

The IZA 2120-LZ comes with an amplifier unit, rack ears (2), AC power cord (5 country specific versions to choose from), plastic feet with locking pins (4), installation and operating guide, 5-pin Euroblock (2), 4-pin Euroblock (2), 2-pin Euroblock (3), jumper wire. The IZA 2120-HZ comes with an amplifier unit, rack ears (2), AC power cord (5 country specific versions to choose from), plastic feet with locking pins (4), installation and operating guide, 5-pin Euroblock (2), 4-pin Euroblock (3), 2-pin Euroblock (3), jumper wires (2).

The amplifiers do come with two rack ears in the accessory bag.

The IZA integrated zone amplifier features a fixed global compressor/limiter, FreeSpace 3 System, FS3B subwoofer, FreeSpace FS2 and FS4, and DesignMax DM2 and DM3 loudspeaker EQ presets, dynamic equalization, Opti-Voice paging, page and auxiliary zoning, detection and prioritization algorithms, and AGC (Automatic Gain Control).

The IZA integrated zone amplifier can easily be adjusted using front panel controls. Source selector and master volume control, located on the front panel, allow a customer to adjust their system for daily operation. Optional Volume control with A/B switch allows the system to be adjusted from remote locations.

Connections can easily be made to the rear panel. No computer is required. The amplifier comes with two rack ear accessories for rack mounting as well as four plastic feet accessories for surface placement.

The FreeSpace IZA integrated zone amplifier is designed to provide optimized performance of FreeSpace 3 System, FS3B subwoofer, FreeSpace FS2 and FS4, and DesignMax DM2 and DM3 loudspeakers. A switch allows the selection of the loudspeaker EQ, or a generic high-pass mode for use with FS3 systems or other passive loudspeakers.

The integrated zone amplifier system will reboot when the power returns and audio will resume.

IZA 2120-LZ

Amplifier power: 2 × 120 W @ 4 Ω; 2 × 60 W @ 8 Ω

Continuous power per channel: 2 × 40 W @ 4 Ω; 2 × 20 W @ 8 Ω

Frequency response: 20 Hz – 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz)

Output channels and connectors: 2 ch/zones, (2) 2-pin inverted touchproof Euroblock connectors

THD+N: ≤ 0.5% (at rated power)

Input channels and connectors: A & B Line: (2) Balanced 5-pin Euroblock and (2) unbalanced RCA pair Page Mic/Line: (1) Balanced 4-pin Euroblock Auxiliary Line: (1) Balanced 1/8-inch (3.5 mm) TRS

IZA 2120-HZ

Amplifier power: 2 × 120 W @ 70/100V

Continuous power per channel: 2 × 60 W @ 70/100V

Frequency Response: 55 Hz – 20 kHz (+0/-3 dB, @ 1 W reference 1 kHz)

Output Channel and Connectors: 2 ch/zones, (2) 2-pin inverted touchproof Euroblock connectors

THD+N: ≤ 0.3% (at rated power)

Input channels and connectors: A & B Line: (2) Balanced 5-pin Euroblock and (2) unbalanced RCA pair Page Mic/Line: (1) Balanced 4-pin Euroblock Auxiliary Line: (1) Balanced 1/8-inch (3.5 mm) TRS

ControlCenter CC-1 and CC-2 zone controllers can be used to control level and source selection.

There are 5 AC power cord variants available for each model:

FreeSpace IZA 2120-LZ integrated zone amplifier

US 120V product code: 719782-1420

AU 240V product code: 719782-2420

Japan 100V product code: 719782-3420

EU 230V product code: 719782-4420

UK 230V product code: 719782-5420

FreeSpace IZA 2120-HZ integrated zone amplifier

US 120V product code: 719782-1410

AU 240V product code: 719782-2410

Japan 100V product code: 719782-3410

EU 230V product code: 719782-4410

UK 230V product code: 719782-5410

POWER SWITCH — ON/OFF AC power.

POWER LED — Solid blue LED indicates the unit is ON. Blinking blue LED indicates the unit is in standby mode.

INPUT SIGNAL LED — LED is green from -39 dBV to 9 dBV, LED goes red over 9 dBV.

OUTPUT LIMIT LED — LED is green from -46 dBFS to -2 dBFS, LED goes red over -2 dBFS, approximately 80 W/channel.

AUX INPUT — 1/8-inch (3.5 mm) stereo line-level input connector. Connection mutes INPUT A and INPUT B for priority override when the AUX INPUT DIP switch is set to “Enabled.”

INPUT A/B Switch — Allows selection of rear line-input channels A or B.

TREBLE/BASS Knobs — Provides ±6 dB adjustment at 7 kHz and 100 Hz.

– IZA 2120-LZ: One set of knobs, allows tonal adjustments of both outputs simultaneously.

– IZA 2120-HZ: Two sets of knobs, allows tonal adjustments of each output independently.

MASTER LEVEL* — Controls the overall system volume for both the loudspeakers and the AUX OUTPUT, when the AUX OUTPUT DIP switch is set to “Variable.” If AUX OUTPUT DIP switch is set to “Fixed” then the AUX OUTPUT goes to maximum level, and changes in the MASTER LEVEL do not affect the AUX OUTPUT level.

* When using a REMOTE volume connection the front panel MASTER LEVEL control becomes disabled.

* When using a REMOTE connection with A/B source selection, either the REMOTE or the front panel can be the MASTER SOURCE control for A/B select, selectable via a DIP switch. MASTER LEVEL control will always be from the REMOTE, and the front panel MASTER LEVEL control becomes disabled.

INPUT A/B — Balanced and unbalanced input connectors.

INPUT GAIN — Allows for -20 dB to +20 dB of adjustment to each INPUT A/B.

PAGE INPUT — Euroblock mic/line input with trigger contact closure for use with push-to-talk microphones.

PAGE INPUT GAIN — Allows for 0 dB to +50 dB of gain control of page input signal.

PAGE INPUT THRESHOLD — Adjusts the level at which signal from the Page input causes other inputs to be lowered.

DIP Switches — A bank of switches to set the amplifier configuration.

REMOTE — Input for volume control with A/B source selection switch (PC 041967).

AUX OUTPUT — Variable or fixed output line-level signal for routing signal to additional audio equipment.

EQ – Provides loudspeaker equalization presets:

– IZA 2120-LZ: IZA 2120-LZ: Flat, FreeSpace FS2, FS4, DesignMax DM2, DM3

– IZA 2120-HZ: IZA 2120-HZ: FS3/HPF, DS 16, DS 40, DS 100 and FS3B (One EQ switch for each output)

MUTE — Contact closure connection that upon trigger (short) will mute all outputs (including AUX OUTPUT).

OUTPUT 1 / OUTPUT 2 TRIM — Allows for up to 40 dB attenuation of the individual loudspeaker outputs relative to the master level.

OUTPUT Connectors — Two inverted touch-proof 2-pin Euroblock connectors for loudspeaker connections.

UPDATE — USB type B female for updating firmware and EQ settings with update utility.

AC Mains Receptacle — Universal AC line voltage input.

The IZA amplifier is appropriate for use in many applications including retail stores, restaurants and bars, hospitality venues, conference rooms, schools and auxiliary zones for large sound systems.

Rear panel DIP switches offer flexible operation modes:

OUTPUT — The outputs can either be set to stereo or mono mode.

A/B SELECT — Master A/B selection can either be front panel controlled or remote controlled.

AUTO STANDBY — If enabled the amplifier will go into auto standby mode after twenty minutes without an input signal.

PAGE BYPASS MASTER — The paging volume can either be set to the master volume or be set at its own independent volume with the rear panel knob.

PAGE MODE — Paging can either mix with the selected input source or duck the input source when activated.

PAGE START — Paging can be activated on either a PTT stimulus or a VOX stimulus.

AUX OUTPUT — The auxiliary output can either have a flat output (without EQ) or with an EQ set from the EQ slide switch.

AUX OUTPUT — The auxiliary output level can either follow the master level when switched to variable, or it can be set to maximum level when switched to fixed.

AUX INPUT — The auxiliary input can either be enabled or disabled. If the auxiliary input is enabled a connection made to the auxiliary input will mute all other inputs.

Rear panel DIP switches offer flexible operation modes:

REMOTE 1 CONTROL — Remote one can be set to control both outputs (zones) simultaneously or each output (zone) can be controlled via its own remote. Each remote has independent A/B selection capability.

A/B SELECT — Master A/B selection can either be front panel controlled or remote controlled.

AUTO STANDBY — If enabled the amplifier will go into auto standby mode after twenty minutes without an input signal. The feature can be enabled (ON) or disabled (OFF) by a DIP switch.

PAGE OUTPUT — Paging can be set to occur in zone one only or both zones.

PAGE BYPASS MASTER — The paging volume can either be set to the master volume or be set at its own independent volume with the rear panel knob.

PAGE MODE — Paging can either mix with the selected input source or duck the input source when activated.

PAGE START — Paging can be activated on either a PTT stimulus or a VOX stimulus.

AUX OUTPUT 1 — Auxiliary output 1 (white) can either have a flat output (without EQ) or with an EQ set from the EQ 1 slide switch.

AUX OUTPUT 2 — Auxiliary output 2 (red) can either have a flat output (without EQ) or with an EQ set from the EQ 2 slide switch.

AUX OUTPUT — The auxiliary output level can either follow the master level when switched to variable, or it can be set to maximum level when switched to fixed.

AUX INPUT — The auxiliary input source can either be output into zone one only or both zones.

AUX INPUT — The auxiliary input can either be enabled or disabled. If the auxiliary input is enabled a connection made to the auxiliary input will mute all other inputs.

OUTPUT VOLTAGE — The output voltage can either be set to 70V or 100V.

Dynamic EQ is a DSP function that ensures full and balanced music at any volume level.

Opti-Voice paging is a DSP function that equalizes the vocal frequency range for clear speech intelligibility while providing seamless transitions.

No. All set up is done locally from the front and rear panels.

The amplifiers are fully protected against loudspeaker output shorts, high temperature damage, and excessively low or high AC line voltage conditions. The IZA 2120-HZ also has an integrated 55 Hz high pass filter to avoid potential transformer saturation.

No. This product must be used indoors. It is neither designed nor tested for use outdoors, in recreational vehicles or on boats.

The IZA amplifiers do not supply phantom power for use with condenser microphones. The IZA 2120-LZ / IZA 2120-HZ will support low impedance signals from dynamic microphones.